Hier entsteht eine Informationssammlung über die Messwertblöcke, Werte Grenzwerte und was sie bedeuten. Die Struktur kann sich ändern, je nach dem die Daten zusammengetragen werden können
---------------------------------------
Motor:2.7l V6/5VT RS4 Benzin
STG Motor 8D0 977 551 (Ersatz für 8D0 909 551)
STG Motor 8D0 977 551 HX (Ersatz für 8D0 909 551 F) MKB: ASJ
STG Motor 8D0 977 551 LX (Ersatz für 8D0 909 551 Q) MKB: AZR
STG Motor 8D0 977 551 KX (Ersatz für 8D0 909 551 K) MKB: AZR
Messwertblock 120
2.Feld Sollwert innere Motordrehmoment Sollwert
3.Feld Istwert innere Motordrehmoment Sollwert
; ECU p/n : 8D0-977.551-HX/LX/KX
; Component: 2.7l V6/5VT RS4
1,0,Engine Idle Speed (specified values listed)
1,1,Engine speed,
1,2,Coolant Temp,80-105C
1,3,O2 Sens Bank1,+/-10%(>2% flct)
1,4,O2 Sens Bank2,+/-10%(>2% flct)
;
2,0,Load Measurement (specified values for idle/2520 RPM)
2,1,Engine speed
2,2,Engine load
2,3,Injection time,2-5/1.6-5ms
2,4,Mass air flow,2.8-5.6/10-15g/s
;
3,0,Throttle Position Sensor check (ign on && eng off -> monitor angle as varied)
3,1,Engine speed
3,2,Mass air flow,g/s
3,3,Throttle angle,0-5deg=closed
3,4,Ign timing,deg
;
;
;004 Kühlmitteltemperatu Motor im Leerlauf
;Feld1 Anzeige der Motordrehzahl
;Feld2 Anzeige der Batteriespannung Sollwert 12,0 ... 15,0V
;Feld3 Kühlmitteltemperatur Temperaturrwert muss gleichmäßig ansteigen Geber für Kühlmitteltemperatur (G62) min
;Feld4 Ansauglufttemperatur von Außentemperatur bis 120°C
4,0,General Engine Data
4,1,Engine speed
4,2,Battery voltage,12-15V
4,3,Coolant temp,80-110°C
4,4,Intake air temp
;
5,0,Engine operating conditions (engine oil temp >80C)
5,1,Engine speed
5,2,Engine load
5,3,Vehicle speed,km/h
5,4,Op condition,idl/prt/fl/dcl/erch
;
6,0,General Engine
6,1,Engine speed
6,2,Engine load
6,3,Intake air temp
6,4,Altitud Corr Factr,-50-20%
;
10,0,General Engine
10,1,Engine speed
10,2,Engine load
10,3,Throttle Drive
10,4,Ignition time
;
11,0,General Engine
11,1,Engine speed
11,2,Coolant temp
11,3,Intake air temp
11,4,Ignition time
;
14,0,Misfire recognition (@idle)
14,1,Engine speed
14,2,Engine load
14,3,Total misfires,0-30
14,4,Misfire status,activated
;
15,0,Misfire recognition cylinders 1-3 (@idle)
15,1,Cyl 1,0-5
15,2,Cyl 2,0-5
15,3,Cyl 3,0-5
15,4,Misfire status,activated
;
16,0,Misfire recognition cylinders 4-6 (@idle)
16,1,Cyl 4,0-5
16,2,Cyl 5,0-5
16,3,Cyl 6,0-5
16,4,Misfire status,activated
;
18,0,Misfires
18,1,Lowest engine,speed@misfire
18,2,Highest engine,speed@misfire
18,3,Lowest engine,load@misfire
18,4,Highest engine,load@misfire
;
20,0,Timing correction
20,1,Cyl 1
20,2,Cyl 2
20,3,Cyl 3
20,4,Cyl 4
;
21,0,More Timing correction
21,1,Cyl 5
21,2,Cyl 6
;
22,0,Knock control Cyl 1&&2 (must road test: RPM>2600 && load>3ms)
22,1,Engine speed
22,2,Engine load
22,3,Ign ang corr 1,0-10deg
22,4,Ign ang corr 2,0-10deg
;
23,0,Knock control Cyl 3&&4 (must road test: RPM>2600 && load>3ms)
23,1,Engine speed
23,2,Engine load
23,3,Ign ang corr 3,0-10deg
23,4,Ign ang corr 4,0-10deg
;
24,0,Knock control Cyl 5&&6 (must road test: RPM>2600 && load>3ms)
24,1,Engine speed
24,2,Engine load
24,3,Ign ang corr 5,0-10deg
24,4,Ign ang corr 6,0-10deg
;
26,0,Knock sensor voltage
26,1,Cyl 1
26,2,Cyl 2
26,3,Cyl 3
26,4,Cyl 4
;
27,0,knock sensor voltage
27,1,Cyl 5
27,2,Cyl 6
;
28,0,Undocumented
28,1,Engine speed
28,2,Engine load
28,3,Coolant temp
28,4,Test status
;
30,0,O2S ctrl op. condition [B=Bank S=Sensor] Fields:[heater on][oper.][ctrl active]
30,1,Status B1S1,111=OK ?
30,2,Status B1S2,100=OK ?
30,3,Status B2S1,111=OK ?
30,4,Status B2S2,100=OK ?
;
31,0,Undocumented
31,1,O2S volts pre TWC
31,2,O2S volts post TWC
31,3,b2 pre TWC
31,4,b2 post TWC
;
32,0,O2S control learning values (before Cat. Conv.) [B=Bank S=Sensor]
32,1,@idle B1S1,+/-10%
32,2,@part B1S1,+/-10%
32,3,@idle B2S1,+/-10%
32,4,@part B2S1,+/-10%
;
33,0,O2S control (before Cat. Conv.) [B=Bank S=Sensor]
33,1,Control B1S1,+/-10%(>2% flct)
33,2,Voltage B1S1,0-1V(>0.3V@30Hz)
33,3,Control B2S1,+/-10%(>2% flct)
33,4,Voltage B1S1,0-1V(>0.3V@30Hz)
;
34,0,O2S aging B1S1 (Temp >80C && engine 1800-2200 RPM until "OK")(Bentley 01-123)
34,1,Engine RPM
34,2,Catalyst?
34,3,Time Period,0.2-2.1s
34,4,Diag Status,ON/OFF|OK
;
35,0,O2S aging B2S1 (Temp >80C && engine 1800-2200 RPM until "OK")(Bentley 01-124)
35,1,Engine RPM
35,2,Catalyst?
35,3,Time Period,0.2-2.1s
35,4,Diag Status,ON/OFF|OK
;
36,0,O2S (beyond Cat. Conv.) [B=Bank S=Sensor] (Bentley 01-126)
36,1,Volt Supply B1S2,0-1V
36,2,Diag Status B1S2,ON/OFF|OK
36,3,Volt Supply B2S2,0-1V
36,4,Diag Status B2S2,ON/OFF|OK
;
37,0,[for 2.7T] Diag O2S ctrl Bank 1 (road test >10 min) (Bentley 01-128)
37,1,Engine load
37,2,O2S Volt S2,0-1V
37,3,Corr val S1-S2,-500-500ms
37,4,Diag Status,ON/OFF|OK
;
38,0,[for 2.7T] Diag O2S ctrl Bank 2 (road test >10 min) (Bentley 01-129)
38,1,Engine load
38,2,O2S Volt S2,0-1V
38,3,Corr val S1-S2,-500-500ms
38,4,Diag Status,ON/OFF|OK
;
43,0,Oxy sensor aging oxygen sensor behind TWC (bank 1) (Bentley 01-131)
43,1,Engine speed
43,2,Catalyst?
43,3,V of O2 sensor,behind TWC (bank 1)
43,4,Diag status
;
44,0,Oxy sensor aging oxygen sensor behind TWC (bank 2) (Bentley 01-131)
44,1,Engine speed
44,2,,Catalyst?
44,3,V of O2 sensor,behind TWC (bank 2)
44,4,Diag status
;
46,0,Cat. Conv. B1 diagnosis (1800-2200 RPM until "Cat B1 OK") (Bentley 01-134)
46,1,Engine speed
46,2,Catalyst?
46,3,Test time, 0-60s
46,4,Diag status,ON/OFF|OK
;
47,0,Cat. Conv. B2 diagnosis (1800-2200 RPM until "Cat B2 OK") (Bentley 01-135)
47,1,Engine speed
47,2,Catalyst?
47,3,Test time, 0-60
47,4,Diag status,ON/OFF|OK
;
50,0,Signals to Engine Control Module (@idle)
50,1,Engine speed
50,2,Spec'd eng spd
50,3,A/C idle boost
50,4,A/C compressor,ON/OFF
;
51,0,Undocumented
51,1,Engine speed
51,2,Spec'd eng spd
51,3,,Count
51,4,,Voltage
;
53,0,Undocumented
53,1,Engine speed
53,2,Spec'd eng spd
53,3,,Voltage
53,4,,Load
;
54,0,Throttle Position at Speed (700-2520 RPM)
54,1,Engine speed
54,2,Op condition,Idle|Part|
54,3,Throt Position,0-100%
54,4,Throt Drive,0-100%
;
55,0,Idle control (@idle)
55,1,Engine speed
55,2,Idle air ctrl,-1.39-+1.39g/s
55,3,Learn value,-1.39-+1.39g/s
55,4,Op condition,00000=OK?
;
56,0,Idle speed stabilization (@idle)
56,1,Engine speed
56,2,Spec'd RPM
56,3,Ctrl Torque Chg,%
56,4,Op condition,00000=OK
;
60,0,Adaptation of throttle valve control mod.(ign on && engine off) (Bentley 01-111)
60,1,Throt Sens 1,3-93%
60,2,Throt Sens 2,97-3%
60,3,
60,4,Adapt status,RUN/OK/ERROR
;
; 61,62,66 from 1.8T
;
61,0,Throttle
61,1,Engine Speed
61,2,Throt Voltage,12-15V
61,3,Throt Drive,0-100%
61,4,Op condition
;
62,0,Ignition on but engine not running
62,1,Throt Sens 1,3-93%
62,2,Throt Sens 2,97-3%
62,3,Throttle Pos,12-97%
62,4,Sender 2 TPS,4-49%
;
63,0,Ignition on but engine not running
63,1,Throttle Pos,12-97%
63,2
63,3
63,4,Adapt status,RUN/OK/ERR
;
64,0,Undocumented
64,1,,Voltage (<1)
64,2,,Voltage (<5)
64,3,,Voltage (<1)
64,4,,Voltage (<5)
;
66,0,Cruise Control
66,1,Vehicle speed
66,2,Brake Position,1000 binary
66,3,Cruise speed,
66,4,Cruise switches,0000 binary
;
70,0,Evap. emissions canister purge valve diagnosis (@idle) (Bentley 01-113)
70,1,Purge vlv open,0-93%
70,2,O2S deviation,+/-15%
70,3,Idle air vlv dev,-1 to 0 g/s
70,4,Status,TestON/OFF|OK
;
71,0,Fuel tank leak detection (@idle) (Bentley 01-116)
71,1,Reed contact,OPEN
71,2,,Error msg
71,3,Sys Status,Test/check/end
71,4,Diag Status,TestON/OFF|OK
;
77,0,Diag of secondary air injection sys (bank 1) (Bentley 01-137)
77,1,Engine speed
77,2,Air mass (g/s)
77,3,Rel. air mass ,sec. air inj.
77,4,Diag status,ON/OFF|OK
;
78,0,Diag of secondary air injection sys (bank 2) (Bentley 01-138)
78,1,Engine speed
78,2,Air mass (g/s)
78,3,Rel. air mass, sec. air inj.
78,4,Diag status,ON/OFF|OK
;
86,0,OBD-II Readiness Code (Bentley 01-101 && 105)
86,1,Readiness Code,00000000=OK
86,2,Cycling flags
86,3,Cycling flags
86,4,Cycling flags
;
87,0,Undocumented
87,1,Ready bits
87,2,Error bits
87,3,Error bits
87,4,Error bits
;
88,0,Undocumented
88,1,
88,2,
88,3,
88,4,
;
89,0,Undocumented
89,1,,Count (0)
89,2,,(OK)
;
90,0,Camshaft adjustment (values are for idle && road test: accel in 2nd gear)
90,1,Engine speed
90,2,Adj ON/OFF,idle=OFF/rt=ON
90,3,Adj resp Bank1,-3-6/16-25degKW
90,4,Adj resp Bank2,-3-6/16-25degKW
;
91,0,Camshaft adjustment (Bank 1)
91,1,Engine speed
91,2,,Load
91,3,,Cam Ctrl. ON|OFF
91,4,,Adj resp Bank1
;
92,0,Camshaft adjustment (Bank 2)
92,1,Engine speed
92,2,,Load
92,3,,Cam Ctrl. ON|OFF
92,4,,Adj resp Bank2
;
93,0,Undocumented
93,1,Engine speed
93,2,Engine load
93,3,,Dig. Idle Stab.
93,4,,Dig. Idle Stab.
;
94,0,Undocumented
94,1,Engine speed
94,2,Cam Ctrl. ON|OFF
94,3,Test Status
94,4,Test Status
;
99,0,O2S Control (ON in read mode && OFF for diagnosis in Basic Setting)
99,1,Engine speed,RPM
99,2,Coolant temp,80-110 C
99,3,PreCat O2 Reg,-10-10%
99,4,O2S control,ON|OFF
;
100,0,Undocumented
100,1,Ready Code,00000000
100,2,Coolant Temp,80-110 C
100,3,Running time
100,4,Diag Status
;
101,0,Undocumented
101,1,Engine speed
101,2,Engine load
101,3,,Avg fuel inject time?
101,4,,0.00 g/s
;
102,0,Undocumented
102,1,Engine speed
102,2,Coolant temp
102,3,Intake air temp
102,4,,inj. on time
;
104,0,Undocumented
104,1,Coolant temp
104,2,,Lambda(-7.8)
104,3,,Lambda (4.7)
104,4,,Lambda 0%
;
107,0,Diagnostic of fuel supply (Bentley 01-118)
107,1,Engine speed
107,2,O2 Control 1,%
107,3,02 Control 2,%
107,4,Diag. status,Test OFF|
;
110,0,Undocumented
110,1,Engine speed
110,2,Coolant temp
110,3,Avg fuel inject time
110,4,Throttle angle
;
111,0,Undocumented
111,1,,0%
111,2,,0%
111,3,,-0.3%
111,4,,1.3%
;
112,0,Abgastemperatur
112,1,°C,Bank1 <980°C;1)
112,2,%,Bank1 90+-5;2)
112,3,°C,Bank2 <980°C;1)
112,4,%,Bank2 90+-5;2)
;1) Kurzzeit können im Einschwingvorgang ca 1025°C erreicht werden
;Eine (Ab-)Regelung setzt erst ab einer Abgastemperatur >980°C
;alle Werte <945°C werden als 945°C angezeigt
;2) Kurzzeit können im Einschwingvorgang 25% erreicht werden
;Anreicherungsfaktor >30% liegt ein Fehler vor
;bei ständig Werten >20% ist evt Kraftstoffdruck zu gering oder
;das LMM Signal zu klein
;
;
; 113-120 from 1.8T
;
113,0,Atmosphere
113,1,Engine speed
113,2,Engine load
113,3,Throttle Drive,0-100%
113,4,Atmos Press,500-1200 mbar
;
114,0,Boost Pressure regulation - Eng load (Bentley 21-18)
;load values in 1-3 can vary by 5% from each other
114,1,Spec'd load, Uncorrected
114,2,Corrected load,
114,3,Engine load
114,4,Wastegate valve,duty cycle
;
115,0,Boost pressure regulation (Bentley 21-14)
115,1,Engine speed
115,2,Engine load
115,3,Spec'd Boost,990-1800 mbar
115,4,Actual Boost,<=1800 mbar
;
116,0,Boost pressure regulation (Bentley 21-17)
116,1,Engine speed
116,2,Fuel Corr Factr,0-20%
116,3,,0%
116,4,Air Corr Factr,0-20%
;
;116? From Bentley: If display field 2 indicates a correction factor <0 %,
;fuel quality is probably incorrect.
;If display field 3 indicates a correction factor <0 %,
;coolant temperature is too high (heat warning lamp lit
;in instrument cluster) or the Engine Control Module is
;
117,0,Boost pressure regulation (Bentley 21-16)
117,1,Engine speed
117,2,Throttle Position,0-100%
117,3,ThrottlesDrive,0-100%
117,4,Spec. Boost,990-1800 mbar
;
118,0,Boost pressure regulation
118,1,Engine speed
118,2,Intake air temp,<=110 C
118,3,Boost Duty Cycle,0-100%
118,4,Actual Boost,<=1800 mbar
;
119,0,Boost pressure regulation
119,1,Engine speed,700-6800 RPM
119,2,,Charge Limit %
119,3,Boost Duty Cycle,0-100%
119,4,Actual Boost,<=1800 mbar
;
120,0,Traction Control (ASR)
120,1,Engine speed
120,2,Spec'd torque,0-399|596 Nm
120,3,Current torque,0-260 Nm
120,4,Status,ON|OFF
;
122,0,Engine torque reduced during shifting (road test)
122,1,Engine speed
122,2,Req. torque,-100-410Nm |599
122,3,Act. torque,-100-310Nm
122,4,,[Text 000 120]
;122,4,Timing retard,act/mtr eng
;
125,0,Undocumented, At Idle
125,1,,Transmission 1
;Abgastemperaturregelung Bank1
220,0,Abgastemperaturregelung
220,1,Motordrehzahl,1/min
220,2,Last,%
220,3,Tastverhältnis B1,%
220,4,Betr.zustand,Text
;Zum Test Motordrehzahl >5000 U/min und Last >100%
;Tastverhältnis 42%+-10% Regelung "ein
;
;Abgastemperaturregelung Bank2
221,0,Abgastemperaturregelung
221,1,Motordrehzahl,1/min
221,2,Last,%
221,3,Tastverhältnis B2,%
221,4,Betr.zustand,Text
;Zum Test Motordrehzahl >5000 U/min und Last >100%
;Tastverhältnis 42%+-10% Regelung "ein
Link zum VAG-COM Labelfile:
8D0-977-551
|
|
